R
FL45200A Series
In-Line Flowmeters with
Half Union Adapters
R
R
Operator’s Manual
An OMEGA Technologies Company
Page 2
CAUTION
FOLLOW INSTRUCTIONS TO AVOID FAILURE
1. Finish piping to be plumb and true.
2. Polysulfone and other exotic plastics cannot tolerate P.V.C. glue and pipe
dope. Even the fumes can cause crazing.
3. Use teflon tape for threaded joints.
4. Make up assembly and fit pipes, then: remove F.M. after glue fumes are
vented out.
5. Meter cannot support attached pipes.
6. Excessive vibration may cause float to give poor reading or cause possible
fracture.
7. Wall, floor, and ceiling mounts to be carefully aligned and sturdy. A support
should be at top and bottom of meter. See drawing.
8. Hand tighten union nuts. No wrenches.
9. Protect meter from ultra violet (UV) rays.
10. VALVES - avoid system that will impose a sudden burst of flow to the meter.
Such a burst will cause the float to impact the guide assembly with destructive
force. Magnet, solenoid, or other quick opening valves cannot be used unless
meter is protected against sudden burst of flow.
11. Failure to comply VOIDS WARRANTY!
Calibration
Part Number
(Hastelloy C Float)
Part Number
(316 SS Float)
GPM
2-20
6-60
8-80
6-100
LPM
8-78
SCFM
M3/HR
FL45201A*
FL45202A
FL45203A
FL45204A
FL45205A
FL45206A
FL45230A
* Teflon® float
-
-
-
FL45202A-HL
FL45203A-HL
FL45204A-HL
30-230
30-300
20-380
80-500
-
-
-
-
-
-
FL45205A-HL 20-130
-
-
FL45206A-HL 25-175 100-675
-
-
-
-
-
40-240
70-400
Page 3
PARTS LIST
1
2
Key Part Number Description
1.
2.
3.
4.
5.
6.
7.
8.
F-452004N Lock Nuts
F-452330N Adaptor
F-452002 Wireholder
3
4
5
F-452043N
O-ring
*Float
6
7
*Meterbody
8
F-452287N Guide Wire
F-452332N Float Stop
*Float & Meterbody must be ordered
as a kit.
Materials of Construction
4-5/8 in.
(117.5 mm)
Meter Body:
Float:
Polysulfone
#316 Stainless Steel or Teflon or
Hastelloy C-276 (Based on model)
# 316 Stainless (opt. Hastelloy C-276)
Polysulfone
Polysulfone
Polyethylene
Guide rod:
Adapters:
Wireholder:
Float Stop:
Union Nuts:
O-Rings:
Nylon
Viton
Scale:
Accuracy:
Permanent, dual scale silkscreen (black ink)
± 2% of full scale reading
18-7/8 in.
(479.4 mm)
Your OMEGA FL45200A Series
Your OMEGA flowmeter was designed to be easy to install.
!
!
Please read the Instruction Guideline on the next page
before installing your flowmeter.
!
This flowmeter is an instrument, special care should be taken
when handling and installing.
Page 4
INSTALLATION INSTRUCTIONS
Remember that you are installing an instrument. Adapters and fittings
should be tightened only enough to prevent leaking. Over tightening
may damage the o-ring seals and threaded fittings.
Never hold the meterbody with pliers or similar tools that may scratch.
Never allow the flowmeter to support the weight of related pipe or
tubing.
Be certain the meterbody is properly aligned with existing plumbing.
Misalignment will put excessive stress on the meterbody and may
result in damage and a decrease in the maximum pressure. If in doubt
regarding proper plumbing procedures, consult a licensed plumber.
The flowmeter must be installed in an exact vertical plane to ensure
accuracy.
Polysulfone is adversely affected by ultraviolet light. Protect the
flowmeter from direct sunlight.
Always use teflon® tape thread sealant. DO NOT use pipe dope
compounds as these products may cause crazing and cracking on the
meterbody.
Do not use solvent based glued (such as PVC cement) while the
flowmeter is fully installed. When using these glues, remove the
meterbody until the glue has cured. Then purge the system before
installing the unit.
Never attempt to solder brass fittings while the flowmeter is fully
installed. The heat required for soldering can damage the flowmeter.
Caution should be exercised when using ball type valves. In some
cases when the valve is opened the float can slam to the top of the
meter causing damage. This “Water Cannon” effect is actually
exceeding the maximum pressure and is not covered under warranty.
Your flowmeter had been designed to be virtually maintenance free.
Should your unit need occasional cleaning, use a mild soap and soft
bottle brush.
Be sure to note the floats “UP” position before disassembling the meter.
Page 5
Ceiling
Caution: Follow these instructions to avoid
failure.
3
2
Danger: Wear eye protection when
installing or removing flowmeter.
1. Polysulfone and other exotic plastics
cannot tolerate PVC Glue and /or pipe dope.
even fumes can cause crazing.
1
2. If you are installing your flowmeter to
a glued pipe configuration, install
3
flowmeter after all glued fittings are dried
and lines are purged of all fumes.
Use Teflon® tape (or similar) for the
flowmeters threaded adapters.
3
5
4
Hand tighten union nuts. No wrenches.
3. Wall, floor, and ceiling mounts are to
be carefully aligned and sturdy. Wall,
floor, and ceiling supports are recom-
mended as needed.
Floor
4. Valves - Avoid a system that will impose a sudden burst of flow to the meter. Such
a burst will cause the float to impact the float stop with destructive force. Magnet,
solenoid, or other quick opening valves cannot be used unless meter is protected
against sudden bursts of flow.
5. The maximum working pressure should not exceed 150 psi at ambient
temperature.
Maximum Temperature vs. Pressure
Temperature
200°F / 93.3°C
190°F / 87.8°C
180°F / 82.2°C
170°F / 76.7°C
160°F / 71.1°C
150°F / 65.6°C
140°F / 60.0°C
130°F / 54.4°C
120°F / 48.9°C
110°F / 43.3°C
100°F / 37.8°C
90°F / 32.2°C
80°F / 26.7°C
70°F / 21.1°C
0 / 0
25 / 1.7
50 / 3.4
75 / 5.2
100 / 6.9
125 / 8.6
150 / 10.3
PSIg / BAR
MADE
IN
USA
WARRANTY
OMEGA warrrantss thiss uunit too be frree of defeccts inn mateerrials aand woorkmannshipp and to give
satisfacttory sseervicee for aa periiood of 13 montthhs fromm datee oof purcchasee. OMEGA Warrranttyy adds
an additioonal oone (11))monthh gracce period too the nnormaall one (11) yeaar prodduct wwarranty to
coverr handdling and shhippiing tiimme. This ensuures tthat OMMEGA’’ss custtoomers rreceiive maximum
coverrage onn eachh pproduucct. If tthe unniit shouuld mallfuncttion, iit mustt be reetturnedd to thhee factoory for
evaluuatioon. OMEGA’ss Custtomerr SService Depaartmeent willl isssuue an AAuuthoriized RReturn (AR)
number immmediaattely uppon phhone oorr written reeqquest.. Uponn eexaminnatioon by OMEGA,, if thhee unit
is found too be deefecttiive it wwill bbe repaireed or replaaced aat no chhargee. Howeever, this
WARRANTYY is vooid if tthe unit shhows evideennce of hhavinng been tammpered witth or sshows
evidence oof beiinng damaaged ass a resuult of excesssive coorrosiion; orr curreent, heat, mmoisttuure, or
vibraation;; improoper speecificcation;; misappplicattion; mmisusee oor otherr operaating ccondittions ooutside
of OMEGA’’s conntrol.. Componennts which wweear or wwhichh are damagged by misuuse arre not
warrantted. Theese incllude conttact poiints, fuusses, andd triacs.
OMEGA is gllad too offeerr suggeestioons on the usse of iit’s vvaariouss prodducts.. Neveertheless,
OMEGAA onlyy warrants tthat tthe parrts manufaacctured by itt willl be ass sspeciffied aand free of
defects.
OMEGA MAAKES NO OOTTHER WARRRANTIESS OR REPRRESENTATTIONS OFF AANY KIND
WHATSOEVVER, EXPRRESSED ORR IMPLIED,, EXCEPT TTHAT OF TIITTLE AND ALLL IMPLIED
WARRANTIIES INCLUUDING ANYY WARRANNTTY OF MERCCHANTABIILITY ANDD FITNESS
FOR A PAARTICUULAR PUURPOSSEE ARE HEEREBY DDISCLAAIMED.
LIMITATIION OFF LIABIILITYY: The rremedies off purcchaseerr set foorth hherein aree excllusive
and thhe tottaal liabbilitty of OMEGA wwith rrespeecct to thhis orrder, whethher baased oonn contract,
warraanty, nnegliiggencee,, indemmnifiiccationn, striict liaabilitty or ottherwwiise, shhall nnoot exceeed the
purchasee pricce of thhe componeent upon whhiich liaabiliity is baseed. In no evvent sshall
OMEGA be lliable foor conseqquentiaall, incideental or sspecial ddamages.
Every preccautiioon for aaccurracy hhaas been takeenn in thee preppaaratioon of tthis manuall; howweever,
OMEGA ENGIINEERRING,, IINC. Neeitheer assumes rrespoonsibbiility ffor anny omisssionns or errors
that may aappeaar nor aassummes liaability forr any ddamaggees thatt resuult from thhe usee of the
productss in accorrdance wiith the infformatioon contaiinned in thiis manual.
SPECIIAL COONDITION: SShoulld thiiss equipment bbe useed in orr withh aany nuucclear iinstaallation or
activvity,, purchaserr willl indeemmnify OMEGA aand hoold OMEEGA haarrmlessss from aany liiability or
damage wwhatsoeveer arisinngg out of thee use of thee equipmennt in suchh a manner.
RETURN REQUESTS / INQUIRIES
Direcct alll wwarrannty annd repair reequessts/iinnquiriies too the OMEGA EENGINNEERIINNG Customer
Service DDepartmennt. BEFORREE RETURNIINNG ANY PRODDUCT(S) TTOO OMEGA, PUURCHASER
MUST OBTAAIN AN AUTTHORIZEDD RETURNN ((AR) NUMBBER FROM OOMEGA’S CCUSTOMER
SERVICE DDEPARTMENNT (IN ORDDEER TO AVOIIDD PROCESSIING DELAYYSS). The asssigned AR
number sshould theen be markkeed on the ouutside of tthe returnn packagee and on any
correspoondence.
FOR WARRAANTY RETUURNS, pleease have
The folloowing infoormation aavailable
Before contacting OMEGA:
1. P.O. nuumber undeer which thhe product
was PURCHASED,
FOR NONN WARRAANNTY REPAAIRS OR
CALIBRAATION, ccoonsult OMMEGA for
current repair/calibration charges. Have
the folloowing infoormation aavailable
before conttacting OMEGA:
2. Model aand seerial nnumbeer of thhe product
under warrranty, and
1. P.O. NNumber too cover thhe COST of
the repair/calibration,
3. Repairr insttructiions aand/orr specific
Problems relative to the Prooduct
2. Model aand seriall number off product,
and
3. Repairr insttructiions aand/orr specific
Problemss relativve to the pproduct.
OMEGA’’s poliicy is tto makkee runniing chaanges,, not moddel chaanges,, wheneever ann iimprovvementt is posssible.
This aaffordss our cuustomeerrs the laatest iin techhnologyy and enngineeerring.OMMEGA iss a regissteredd tradeemark of
OMEGA ENGIINEERRIING, INNC.©Coopyrigght 1995 OMEGGA ENGIINEERIING, INNC. Alll rights resserveedd. This
docummentattion maay not bee copieed, phottocopiied, repproducced, trraanslateed, or rreduceed to anny elecctronic
mediuum or mmaachinee-reaadable formm, in wwholee oor in paart, wwithout wriittenn consseent of OMEGA
ENGINEERRING,, INC.
Where Do I Find Everything I Need For
Process Measurement and Control?
OMEGA... Of Course!
TEMPERATURE
Thermocouple, RTD & Thermistor Probes, Connectors, Panels & Assemblies
Wire: Thermocouple, RTD & Thermistor
Calibrations & Ice Point References
Recorders, Controllers & Process Monitors
Infrared Pyrometers
PRESSURE / STRAIN FORCE
Transducers & Strain Gauges
Load Cells & Pressure Gauge
Displacement Transducers
Instrumentation & Accessories
FLOW / LEVEL
Rotameters, Gas Mass Flowmeters & Flow Computers
Air Velocity Indicators
Turbine / Paddlewheel Systems
Totalizers & Batch Controllers
pH / CONDUCTIVITY
pH Electrodes,Testers& Accessories
Benchtop / Laboratory Meters
Controllers, Calibrators, Simulators & Pumps
Industrial pH & Conductivity Equipment
DATA ACQUISITION
Thermocouple, RTD & Thermistor Probes, Connectors, Panels & Assemblies
Wire: Thermocouple, RTD & Thermistor
Calibrations & Ice Point References
Recorders, Controllers & Process Monitors
Infrared Pyrometers
HEATERS
Heating Cable
Cartridge & Strip Heaters
Immersion & Band Heaters
Flexible Heaters
Laboratory Heaters
ENVIRONMENTAL MONITORING AND CONTROL
Metering & Control Instrumentation
Refractometers
Pumps & Tubing
Air, Soil & Water Monitors
Industrial Water & Wastewater Treatment
pH, Conductivity & Dissolved Oxygen Instruments
M-2062/0904
|
Miele Ventilation Hood DA5190W User Manual
MTD Lawn Mower i1046 i1050 User Manual
MTD Snow Blower 31AH5C3F401 User Manual
NEC Home Theater System PX602UL BK User Manual
Nextar Digital Photo Frame N5 105 User Manual
NordicTrack Treadmill NTL12944 User Manual
Nostalgia Electrics Beverage Dispenser BC 4600 User Manual
Omega Engineering Oxygen Equipment Dissolved Oxygen System User Manual
Omega Weather Radio CNI16 User Manual
Panasonic Cell Phone A210 User Manual